vigo sliding glass doors

If the threshold is too long, cut it with a hacksaw until it fits the opening. Replace the plates and screw them into the plastic anchors with the hex screws (#19) . shower sliding glass door frameless frosted vigo inch doors email shopping Once everything is level and plumb then you can begin your drilling. Slide the bracket body in position on the structural rail. Place the two top rollers and the door panel (#5) assembly onto the structural rail (#10) . This shower door is crafted with quality tempered glass and 304-series stainless steel hardware and features an eye-catching round roller disk sliding system and sleek door handle. VIGO strongly recommends this installation be completed by a licensed professional. Align the plates to the rail and slide the bracket body over the plate. You should use the wood framing from behind the face edge of the stall to provide a secure mounting to the door . Note: There is a 5mm horizontal adjustment in the structural If adjustments are needed, remove the fixed panel holder cover to expose the hollow hex screw. door frosted frameless tub chrome glass sliding vigo expanded open

E1 . SCAN TO WATCH THE ROLLERDISK TECHNOLOGY VIDEO. Position the fixed panel (#4) and the structural rail assembly (#10) correctly using a level. You may need to adjust the direction of the small hex hole to meet your needs. Installation of door unit requires at least two people. The recommended framing and dimensional requirements are shown for a typical application and may vary depending on the site requirements. vigo Lock the bracket body to the plate with the supplied alien key (note the screws should be at the top of the tail). Apply clear silicone caulking along the fixed panel and threshold of the shower enclosure interior. If you have any questions contact VIGO Tech Support at 1-866-591-7792. This Installation Guide uses the following symbols to indicate important information. Handle fragile items with care to prevent personal injury or material damage. Place rail into the cabin opening. Note that the end of the threshold should go halfway inside the bottom door guide. These Instructions must be observed for safe installation. Proper planning is imperative for proper installation. Remove the fixed panel holder cover. 1]. Trim the flange on the seal strip so that there is enough clearance for the door to roll without the seal strip hitting against the rollers. Remove the rollers (#3) from the box, note that these are fully assembled. E3 . WARNINGInstructions that, If Ignored, could result In death or serious personal Injury caused by Incorrect handling or Installation of the product. Position the vertical rail against the wall, making sure the bottom rests on the floor or base or tub for tub model. Install the plate by drilling holes at your markings and place the white plastic anchors (#16) inside them. F1 . Tighten the handle nuts from inside the shower. Fully tighten the adjustment screws and re-install the roller caps. If the rail is too long, cut it with a hacksaw to fit the opening. Comment document.getElementById("comment").setAttribute("id","a6d22879d3f166fdb5ddf0ff9440e8bb");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. Remove the threshold. With the brackets mark the wall at the center portion of the plate.

frameless vigo rollerdisk alcove Align the threshold and press firmly down. Fig. The textured side of the matte glass unit should always be installed on the outside of the unit. Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower door . The wall mount brackets for the structural rail have 13mm of built-in adjustability and the fixed panel holders have up to 10 mm built-in adjustability to ensure that your VIGO product is easy to install and accommodate minor adjustments, such as out-of-plumb walls. Start at the bottom of the glass and work your way up, using the heel of your hand to firmly press the seal strip onto the glass. shower door frameless vigo doors sliding frosted glass chrome inch hayneedle shower Please check our website at www.vigoindustries.com for additional information or instructional videos. Place plastic anchors (#15) inside them. Using an alien key, make your adjustments. With the with the markings on the wall. Place plastic washers (supplied) on each side of the door. By not leveling the unit during construction the unit may leak causing possible water damage. Note that the rollers have a built-in mechanism that will provide adjustment for walls that are not 100% perpendicular to the floor. There seems to be a problem serving the request at this time, {"modules":["unloadOptimization","bandwidthDetection"],"unloadOptimization":{"browsers":{"Firefox":true,"Chrome":true}},"bandwidthDetection":{"url":"https://ir.ebaystatic.com/cr/v/c1/thirtysevens.jpg","maxViews":4,"imgSize":37,"expiry":300000,"timeout":250}}, Vigo Industries VG6041STCL5274 Elan Adjustable Frameless Sliding Shower Door, Vigo VG6021MBCL6076 Wide Sliding Frameless Shower Door, Vigo 60 Inch Clear Glass Frameless Tub Sliding Door, Vigo Vg60216066 Elan 66"h X 60"w Sliding Frameless Tub Door - Chrome, Vigo Vg60415274 Elan 74" High X 52" Wide Sliding Frameless Shower Door With, Vigo Vg60417274 Elan 74" High X 72" Wide Sliding Frameless Shower Door With, Vigo Vg60414874 Elan 74"h X 48"w Sliding Frameless Shower Door - Black, Vigo Caspian 61" X 73.5" Double Sliding Frameless Shower Door Chrome. Apply silicone to the threshold around the inside and outside of the shower base. Mark holes on the wall for the 4 mounting screws. Use a level to be sure the rail is straight. C3. B3. shower frosted glass door sliding inch vigo frameless doors frameless vigo curbappeal choosing showers 1], Loosen the hex screw to allow for movement. Note: Preferred method of installation negates anchors and has the installation going right into the studs. B5. When installing, the center dimension of the wall mount bracket plate to the curb is 75 1/2 for the shower door model and 55 3/4 for the tub door model and the center dimension of the wall mount bracket plate to the center of the vertical rail is 7/8. Make sure to cut the rail on the door side only. You must have JavaScript enabled in your browser to utilize the functionality of this website. B8. Line the outside of the wall mount brackets with the markings on the wall. Place the threshold (#8) into the bottom door guide (#7). Replace the vertical rail and screw it into the plastic anchors with the Philips screws (#17). Use the provided alien key to unscrew the adjustment screw and dismantle the roller. F2 . Carefully review the Parts List on page 2. There is a 5mm adjustment built in. Maintenance and other important non-personal injury and non-material damage instructions or statements that should be observed. NOTE: Prior to any installation, mark lines on the floor and wall for proper dry fit. VG6043VIGO LUCA Adjustable Frameless Sliding Shower Door, ANSI Z97.1 and 16 CFR 1201-certified glassAll VIGO Shower Door have a Limited Lifetime Warranty. Copyright 2019 VIGO Industries. Your actual dimensions may vary. Electric drill; 3/32, 1/8 11 or 3/16 11 drill bit (According to wall). 3. Due to individual site variations, exact guidelines for every situation cannot be supplied . hardware Place the door panel (#5) into the shower first making sure to rest the glass in a manner that the glass or base/tub does not incur damage. There is a 3/8 adjustment in the roller to use in the case that your walls are not plumb and level. Never attempt to do so . A3. NOTE: INSTALLATION MUST BE DONE BY A QUALIFIED, LICENSED PROFESSIONAL. elan Note: There is a 5mm adjustment in the wall mount bracket plates. For optimum performance, you should install the shower door perfectly level on a level surface. B7. The clear glass model has a reversible door and can be installed to the right or left side. Note: The measurements of 55 3/4, 761/2 and 7/8 should just be used as a guide. [SEE FIG. C1. Start at the bottom and work your way up, using the heel of your hand to firmly press the seal strip onto the glass. vigo Install the plate by drilling holes at your markings and place the white plastic anchors (#16) inside them. If necessary, loosen the adjustment screw and rotate the individual roller. If your wall is off on the bottom, the rollers should be adjusted as shown in Fig. Your actual dimension may vary. Attach side seal strip (#11) to handle side of the door. B4. D1. Screw the two bottom roller guides (#20) to the door panel (#5) using the alien key supplied. Apply clear silicone caulking along the wall and floor of the shower enclosure interior. chrome on VIGO VG6043 Luca Adjustable Frameless Sliding Shower Door Installation Guide, Roller adjustments to accommodate out of square openings, VIGO VG6043 Luca Adjustable Frameless Sliding Shower Door, Essence Shower/Tub Door Installation Instructions Manual, ENIGMA-XO Shower And Tub Door Installation Instructions, SFA Douche/Shower Flat Installation Guide, IKEA MORLIDEN Glass Door Installation Guide, Luca Adjustable Frameless Sliding Shower Door, VG6043 Luca Adjustable Frameless Sliding Shower Door, IKEA 802.228.27 MSTERLIG Hob/Booster Instruction Manual, adastra RMC120 Series Rackmount 100V Mixer-Amplifier with CD player User Manual, Srichpk P36A-Black Smart Watch User Manual, Shanghai Laisi Information Technology 2021AG Smart Rope User Manual, Pocket Juice Wireless Charging Power Bank User Manual, ZERFUN G8 Pro Wireless Microphone System User Manual, Airrex Infrared Heater AH-200/300/800 User Manual, 2017 Toyota Camry Hybrid LE Fuse Box Diagrams, 2017 Mitsubishi Lancer 4WD Fuse Box Diagrams, Mitsubishi Lancer Passenger and Engine Fuse Box Diagram, Mira Honesty ERD Bar Valve and Fittings User Manual, Built-in horizontal adjustability makes this shower door easy to install, Constructed from ANSI Z97.1 and 16 CFR 1201-certified tempered glass for added safety, RollerDisk Technology allows for up to 3/8of adjustabilily as walls shift over time, High-quality stainless steel and solid brass hardware resist corrosion and tarnishing, All VIGO Shower Doors feature a quality assured Limited Lifetime Warranty. V1GO Product Support (866) 591-7792 (Option 2) Monday- Friday 9.30am 5 30pm EST. This will raise or lower the height that the roller sits on the structural rail. C5. Always observe the instructions indicated by these symbols. The measurements of 70 7/16 or 62 3/8 should just be used as a guide. Remove the vertical rail and drill holes. frosted frameless vigo claygate Verify that the overall size of the shower door opening is appropriate for the shower enclosure . elan frameless vigo bypass mfr Place the fixed panel with the pre-installed vertical seal strip into the vertical rail. A2. Compare items on your invoice with what you have received. RollerDisk Technology - Sliding roller disks with 3/8" built-in adjustability as walls shift over time, ANSI Z97.1 and 16 CFR 1201 certified glass, All VIGO shower doors have a Limited Lifetime Warranty. A5. To prevent damage to the finish, you should protect the shower cabin bottom with a cardboard protector before beginning the installation. If any items are missing, please call VIGO Industries at 1-866-591-7792. VIGO reserves the right to modify/update all hardware and glass components based on bettering the product for the end users experience. Verify that the bottom of the door rests in the back notch of the bottom door guide (#7). C6 . Replace the plates and screw them into the plastic anchors with the hex screws (#19) . B6. B1. Carefully unthread the cap with a small head alien key. A4. If your wall is off on the top, the rollers should be adjusted as shown in Fig. 4. 2. Attach the seal strip (#12) to the fixed panel.

[See Fig. Lightly lift and slide the bottom door guide (#7) half way under the fixed panel making sure that the glass is level and plumb. A1. Place the fixed panel holder through the hole in the fixed panel, replace the cover and tighten. JavaScript seems to be disabled in your browser. D2 . (see configuration diagram below). Mark the location of the wall mount brackets on the wall. Serious or fatal crushing injuries can occur from furniture falling down.. Preferred method of installation negates anchors and has the installation going right into the studs. Copyright 1995-2022 eBay Inc. All Rights Reserved. glass door frosted frameless tub sliding vigo stainless steel left shower expanded open inch View cart for details.

Your email address will not be published.

In order to activate your warranty, you must register your product.

Place the screw through door panel top holes and attach the two top rollers onto the door panel (#5). frameless vigo glass door tub clear sliding inch chrome tempered VIGO Elan Adjustable Frameless Sliding Shower Door, Built-in horizontal adjustability makes this shower door easy to install, Constructed from ANSI Z97.1 and 16 CFR 1201-certified tempered glass for added safety, RollerDisk Technology allows for up to 3/8"of adjustability as walls shift over time, High-quality stainless steel and solid brass hardware resist corrosion and tarnishing, All VIGO Shower Doors feature a quality assured Limited Lifetime Warranty, Fixed panel with sliding shower door for walk-in shower entry, Reversible left or right side opening installation, 3/8" ANSI Z97.1 and 16 CFR 1201-certified clear tempered glass, Glass is pre-drilled for door handle installation, Top rail support ensures wall anchoring and reinforces wall stability, Single water deflector redirects water toward the inside of the shower, Quality 304-series stainless steel constructed hardware in a stainless steel finish, guaranteed to never rust, Rails are stainless steel tubes with reinforced walls, built to withstand more than the required weight, Full-length clear seals make the shower waterproof where door and side panel overlap, Allows 4" of horizontal adjustability for your sizing needs and adaptability to ensure your VIGO product will continue to function properly as your walls expand and contract over time. You will see a big hex screw, this is referred to as the roller height adjustment screw. G1 . sliding frameless vigo elan vigoindustries jossandmain 1A displays the 3 different positions. Place the threshold back into its shower base location. B2. Attach the door panel seal strip (#21) to the door glass with the flange pointing away from the shower. It is important to perform a dry fit prior to install. Apply a bead of silicone between the walls and base of the stall. Untighten the plates from the wall mount brackets and center the plates to the wall markings. Home VIGO VIGO VG6043 Luca Adjustable Frameless Sliding Shower Door Installation Guide, Model No. vigo elan frameless sliding The matte glass model is not reversible and the direction of installation is specific to the model number. Something went wrong. E2 . Cover set screws with the supplied screw covers (#22) . Apply silicone to the underside of the threshold. Please refer to pages 20-21 for Roller Adjustments to Accommodate Out of Square Openings Once the rollers are properly adjusted and the door sits flush against the wall in the closed position, the adjustment will be complete. frameless vigo sliding chrome shower inch door glass If the rail is not level then loosen the bracket body, slide out of the way and adjust the plate as needed. Vigo 34-in Zenith Fixed Frame Clear 3/8" Tempered Class Glass Reversible Shower Screen in Matte Brushed Gold Finish, VIGO Orion Clear Curved Bathtub Door in Antique Rubbed Bronze, VIGO Elan 68" Frameless Shower Door, 3/8" Clear Glass/Stainless Steel Hardware, VIGO Ryland 62" Frameless Shower Door, 3/8" Clear Glass/Stainless Steel Hardware, Vigo Caspian 59 to 61 in. B9. All rights reserved. Make sure the structural rail is level. Fiberglass, acrylic or sheetrock construction might not be sufficiently strong enough to support the shower door enclosure. IT IS HIGHLY ADVISED TO DRY FIT THE UNIT PRIOR TO ANY INSTALLATION. Place the handle to the position on the door . bvseo-msg: HTTP status code of 404 was returned; vigomarketing-1037e0fce53008d709351bbda2d437ed, msnbot|google|teoma|bingbot|yandexbot|yahoo, Mozilla/5.0 (Linux; Android 10; K) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/103.0.0.0 Mobile Safari/537.36, https://www.vigoindustries.com/elan-frameless-shower-door-375-in-vg6041-2347, http://seo.bazaarvoice.com/vigomarketing-1037e0fce53008d709351bbda2d437ed/Main_Site-en_US/reviews/product/1/VG6041.htm.

If your walls are plumb and level, follow the configuration in Fig. Then place the alien key in the small hex hole as shown and roll it to the right or left to make the adjustment. If there is insufficient enough support, then reinforce the shower walls with wooden studs prior to shower door installation. For a custom look, this door can be installed to slide open left or right. Square and/or Phillips #1 and #2 screwdriver. Unscrew the handle holders from the handle assembly (#6) . Place the wall mount brackets (#1) on both ends of the structural rail and lightly lighten for dry fit purposes. The glass panels are tempered and cannot be cut. Essence Shower/Tub Door Installation Instructions Manual - Optimized PDF Essence Shower/Tub Door Installation Instructions Manual - Original PDF, ENIGMA-XO Shower And Tub Door Installation Instructions - Optimized PDF ENIGMA-XO Shower And Tub Door Installation Instructions -, DOUCHE FLAT SHOWER FLAT 144 02.15 UNITED KINGDOM SANIFLO Ltd., Howard House, The Runway South Ruislip Middx.,, IKEA MORLIDEN Glass Door Installation Guide WARNING! A, B & C dimensions were measured after shower enclosure was completely installed. With its classic roller sliding door and sleek modern design, the VIGO Elan Frameless Sliding Shower Door provides the ultimate in contemporary design for your bathroom. There is a 5mm adjustment on the vertical rail (based off the depth of the track) for any minor adjustments. Frameless Sliding Shower Door in Chrome with Clear Glass and Handle, VIGO Elan 52" Frameless Shower Door, 3/8" Clear Glass/Chrome Hardware, VIGO Ryland 48" Frameless Shower Door, 3/8" Clear Glass/Stainless Steel Hardware, VIGO SoHo 26" Adjustable Frameless Shower Door with Clear Glass and Stainless Steel Hardware. C2. NOTE: These adjustments are approximate. x 73.5 in. Remove the rail from the dry fit and remove the wall mount brackets from the structural rail. Remove any excess silicone from the threshold. Using an alien key, you will be able to adjust the roller to accommodate for the variance. C4. 1 product ratings - Vigo VG60416066 Elan 66"H x 60"W Sliding Frameless Tub Door - Chrome, 1 product ratings - Vigo VG60416074 Elan 74"H x 60"W Sliding Frameless Shower Door - Stainless Steel, Shower Head Holders, Shower Arms & Slide Bars.

Sitemap 9

vigo sliding glass doorsnavy blue pants women